C series remote I/O
-
CT-7346 18 channels field power distribution module（24VDC/0VDC/PE）
Module features
◆ Support on-site power distribution, output is 24VDC/0VDC.
◆ Support expansion of 18 channels ,6 channels of 24VDC ,6 channels of 0VDC ,6 channels of PE.
◆ Requires no configuration and occupies no slot in configuration. -
CT-7220: Power Supply Extension Module 5V/2A
CT-7220 Power Supply Extension Module 5V/2A
◆ System Power and Field Power Extension
◆ System Power Output 2A@5VDC
◆ Field Power Extension 8A Current
◆Take no module channel(replace CT-7221) -
CT-623F: 8 digital input&8 digital output /24VDC/ source or sink
CT-623F: 8-channel digital input /24VDC/ source or sink type & 8-channel digital output /24VDC/ source type
Module features
◆ The module supports 8-channel digital input, and supports source type and sink type two-way input. The input voltage is 0V/24VDC.
◆ The module supports 8-channel digital output, Output high level valid, and the output voltage is 24VDC.
◆ Module input channel can collect digital output signal of field equipment. (dry contact or active output)
◆ The module input channel can be connected to the 2-wire or 3-wire digital sensor.
-
CT-5321: Modbus Serial Port Module
CT-5321 Modbus Serial Port Module
1 Module Description
The Modbus serial port module supports 1 channel RS485/RS232 /RS422(optional), supports Modbus RTU/ASCII protocol, and supports master, slave and free transparent transmission mode.
The serial Module CT-5321 could be applied with the adapter modules, so it could convert Modbus into other protocols such as Modbus TCP, Profinet, EtherCAT, EtherNet/IP, etc. When the module is used, serial port parameters and Modbus instructions should be configured in IO Config software.
Devices with RS485/RS232/RS422 interface, which support modbus-RTU/ASCII, could be applied with CT-5321 to realize interconnection with upper PLC or upper computers. CT-5321 could be applied with devices such as: PLC, DCS, remote IO, VFD, motor start protection device, intelligent high and low voltage electrical apparatus, power measurement device, intelligent field measurement equipment and instruments, etc.
-
CT-5721: Bus extended slave module
CT-5721 Bus extended slave module
The bus extened slave module is used to extend the bus.The bus extended slave module has no process data and configuration parameters.
-
CT-5801: Terminal module
CT-5801: Terminal module
Terminal modules are used to stabilize the internal bus communication.Each C series I/O protocol adapter must be equipped with 1pc of terminal module CT-5801 no matter how many sub-modules are connected.
The dustproof terminal could cover the internal bus and field power supply hardware of the last IO module.
And terminal modules have no process data and configuration parameters.
* Take no module channel and replace CT-5800.
-
CT-5112 2-channel encoder input/24VDC
Module features
◆ the module supports two channels of encoder input.
◆ each encoder channel supports A/B incremental encoder or pulse-directional encoder input.
◆ each encoder channel supports orthogonal A/B signal input, input voltage 24V, and it supports source and sink input.
◆ the incremental encoder mode supports x1/ x2 / x4 frequency multiplication mode.
◆ the pulse – direction mode supports nondirectional signal, pulse input only.
◆ each encoder channel supports 1 digital input signal with an input voltage of 5Vdc or 24Vdc.
◆ each encoder channel supports 1 digital output signal with an output voltage of 24Vdc.
◆ each encoder channel supports 1 way of 24V power output, which can be connected to the encoder for power supply.
◆ the module internal bus and field input adopt magnetic isolation.
◆ the module carries 16 LED indicators.
◆ the maximum input frequency of the encoder supported by the module is 1.5MHz.
◆ the module supports measurement function, it could detect the load speed or input signal frequency.
-
CT-5711: Bus extended master module
CT-5711 Bus extended master module
Module Description
The bus extened master module is used to extend the bus.The bus extended master module has no process data and configuration parameters.
-
CT-222F: 16 channel digital output/24VDC/source type
CT-222F 16 channel digital output/24VDC/source type/output 24VDC, the output high level is valid
Module features
◆ the module supports 16 channels digital output, the output high level is valid, the output voltage is 24VDC.
◆ module can drive field equipment. (relay, solenoid valve, etc.)
◆ the internal bus of the module and field output are using opto-coupler.
◆ the module has 16 digital output channel LED indicator light.
◆ the module has the functions of thermal shutdown and overcurrent protection.
◆ the module supports short circuit protection and overload protection.
-
CT-122F: 16 channels digital input/0VDC/Source type
CT-122F 16 channels digital input/0VDC/Source type/Input 0V, the input low level is valid
Module features
◆ the Module supports 16 channels digital input, supports source input, the input voltage is 0V and the input low level is valid.
◆ the module could collect the digital output signal of field equipment (dry contact or active output).
◆ the module can be connected to a 2-wire or 3-wire digital sensor.
◆ the internal bus of the module and field input are isolated by optocoupler.
◆ the module supports input signal holding function, holding time can be set.
-
CT-221F: 16 channels digital output/24VDC/Sink type
CT-221F 16 channels digital output/24VDC/Sink type/output is 0V, the output low level is valid
Module features
◆ the module supports 16 channels digital output, the output voltage is 0V and the output low level is valid.
◆ the module can drive field equipment (relay, solenoid valve, etc.)
◆ the internal bus and field output of the module both adopt electromagnetic isolation
◆ the module carries 16 digital output channel LED indicator
◆ the module has the function of thermal shutdown and over current protection
-
CT-124D 32-channel digital input/24VDC/Sink or Source
◆ The module supports 32 channels of digital input, supports high-level input, and could be connected to PNP sensor, and supports low-level input, and could be connected to NPN sensor.
◆ The module can collect the digital output signal (dry contact or active output) of the field device.
◆ The module can be connected to 2-wire or 3-wire digital sensor.
◆ The internal bus and field input of the module are isolated by optocoupler.
◆ The module supports the input signal holding function, and the holding time can be set.
◆ After adding the counting submodule, the counting function is available.
◆ Each input channel of the module supports 32-bit counter, and the counting frequency < 200Hz.
◆ The module can set the digital signal input filtering time and counter byte transmission sequence.
◆ The module can independently set the counting mode and counting direction for each channel.
